How to change Vaporesso SWAG Settings

As a vaping device, Vaporesso Swag is adopting 15 different designs that can be the perfect choice to enhance your style. Inside the compact structure, Vaporesso Swag is powered by a powerful 18650 mAh battery to support your whole day vaping mood. The NRG SE tank attached can perfectly interact with OMNI Board 2.0 to satisfy you on every single puff. However, it’s essential to know how to use Vaporesso Swag properly before your adventure with it. Therefore, please go through the details of Vaporesso Swag settings so that you can get familiar with your beloved device in a short period

General Settings:
 
1.Switching On/Off & Vaping
Press the fire button 5 times within 2 seconds to turn ON/OFF the device. Hold the fire button and inhale through the mouthpiece. Release the fire button and exhale.
 
1.Adjustment Buttons Lock/Unlock:
When power on, keep pressing the mode button and up button simultaneously for two seconds to lock/unlock your device.
 
1.Switch Display Mode:
Keep pressing up button and down button simultaneously for two seconds to rotate the screen display 180 degrees.
 
1.Switch Vaping Modes:
Long press the mode button for three seconds to switch among VW (H/N/S) / VT (Ni200, SS, Ti) / TCR / BYPASS / CCW / CCT modes.
 
1.Adjusting Air Flow & Filling E-liquid
Twisting the air ring around the bottom of the tank to adjust airflow. And screwing out the lip on top to fill the E-liquid into the chamber.  

Atomizer Settings:
 
1.Changing Atomizer
Unscrew the base to remove and insert a new atomizer. To update the coil within atomizer, unscrew the base first, then pull the EUC out from the base and add a new one. Screw the base back. Wait a while after replacing to make sure the coil primed.
 
1.Automatic Atomizer Recognition:
The mod will read the coil’s resistance as soon as the connection is detected. It will also recognize coil type when a KANTHAL coil attached, and the mod will shift from TC to wattage mode automatically.
Meanwhile, to achieve a better temperature control effect, the mod will also ask the user if a new atomizer is attached. “OLD LOAD: -, NEW LOAD: +” will appear on display. If a new atomizer is connected, press up button, the mod will read further resistance; if not, press down button, the mod will read at locked resistance.

Mode Settings:
 
·Smart VW mode:
As an advanced Variable Wattage mode, there are 3 levels of VW: H stands for High; N stands for Normal; S stands for Soft.
 
·In CCW mode:
While on VW mode, press the mode button three times consecutively to select CCW. Select and hold down the mode button to confirm and to implement any modifications to the wattage line using the plus and minus buttons.
 
·In TC-Ni/TC-Ti/TC-SS/TCR (M1, M2) mode:
In TC-Ni/TC-Ti/TC-SS mode, the OMNI Board 2.0 allows you to change the startup wattage under temperate control mode.
The Setting of TCR Mode (M1, M2):
When set in TC-Ni/TC-Ti/TC-SS mode, and the device is powered on, you will enter into the TCR (M1, M2) set menu, by clicking mode button 3 times:
1.Press mode button to choose among M1, M2;
2.Press the up or down button to increase or decrease the TCR value according to material of the coil you used;

Adjust temperature: In TC-Ni/ TC-Ti/TC-SS/TCR (M1, M2) mode, temperature can be adjusted from 100-315°C or 200-600°F by pressing up button or down button. Long press up button or down button can rapidly increase or decrease temperature settings.
Lock/Unlock resistance: In TC-Ni/TC-Ti/TC-SS/TCR (M1, M2) mode, press down button and mode button simultaneously for 2s will lock/unlock the resistance level. Attach a new atomizer will not change the locked resistance.
 
·In CCT mode:
While on any TC mode, press the mode button three times consecutively to select CCT. Select and hold down the mode button to confirm and implement any modifications to the temperature line using the up and down buttons.
 
·In Bypass mode:
Direct output voltage system is applied in Bypass mode. The higher the battery level is, the higher the output voltage is.
 
·Default:
You could reset to default setting by entering Default and pressing YES.